May 11th, 2010
The ICL7660 CMOS Voltage Converter can be connected to function as voltage doublers in order to generate output voltage. The schematic herein appears positive voltage doubling circuit using the ICL7660.
In this circuit, the pump inverter switches of the ICL7660 is used to charge C1 to a voltage level of the supply voltage (V+) and the forward voltage drop (Vf) of diode D1. Voltage on C1 plus the supply voltage is applied through diode D2 to capacitor C2. And the source resistance of the output will depend on the output current.
Positive Voltage Doubling Circuit using ICL7660 Voltage Doubler continued »
Tags: Circuit Diagram, Datasheet, ICL7660, positive voltage, voltage doubler
Posted in Datasheet Application | No Comments »
May 10th, 2010
The ICL7660s are unique monolithic CMOS power supply circuit which offer simple conversion of +5V Logic Supply to -
+5V Supplies, Simple Voltage Multiplication, wide operating voltage range, and can also be connected to function as voltage doublers for generating output voltages up to +18.6V with a +10V input.
The herein document contained principles and applications of the ICL7660 CMOS voltage converter such basic voltage doubling operation, negative supply for supply voltages below 3.5V, Output Ripple, Paralleling ICL7660 and ICL7660A to reduce output resistance, Cascading Devices, External Clocking, Positive Voltage Doubling, Voltage Splitting, and Regulated Negative Voltage Supply.
ICL7660 CMOS Voltage Converter Circuit Applications continued »
Tags: CMOS Voltage Converter, icl7660 datasheet, voltage doubler IC
Posted in Power Supply | No Comments »
May 10th, 2010
The following schematic shows Hood Louver Driver Circuit Diagram using IC LM393. This circuit uses an LM393 op-amp comparator (U1) to monitor the Throttle Position Sensor (TPS) voltage. As seen in the diagram, the output of the LM393 drives a high-current PNP transistor (Q2), which turns on/off the hood louver solenoid relay.
As also stated in the LM393 datasheet, the advantages of LM393 are High precision comparators, Compatible with all forms of logic, Power drain suitable for battery operation, Reduced Vos drift over temperature, and more.
Hood Louver Driver Circuit Diagram using IC LM393 continued »
Tags: hood louvering, lm393 circuit, lm393 comparator, LM393 datasheet
Posted in Power Supply | No Comments »
May 3rd, 2010
Splitting a higher supply in a half using ICL7660 and or ICL7660A in bidirectional characteristic is shown in the following circuit diagram. The combined load will be evenly shared between the two sides.
With this voltage splitting and then a cascading ICL7660 and ICL7660A circuit, +15V can be converted to -15V.
ICL7660/ICL7660A Voltage Splitting Circuit Diagram continued »
Tags: icl7660 circuit, icl7660 datasheet, voltage splitting
Posted in Power Supply | No Comments »
May 2nd, 2010
There is a rapid power-down condition when a power supply short circuit or when there is a poorly filtered power supply. CD4538B series CMOS Dual Precision Monostable Vibrator has the Power-Down Mode feature to avoid possible device damage in this mode.
As seen in the circuit diagram, in such mentioned condition above, the energy stored in Cx could discharge into Pin 2 or 14 of the CD4538B IC. In order to avoid device damage when Cx is bigger than 0.5uF, a 1A or higher (1N5395 or equivalent) of protection diode and a separate ground return for Cx should be provided.
See the CD4538B datasheet for completed CD4538B Rapid Power Down Protection Circuit Diagram (source: littlediode.com).
Tags: CD4538B datasheet, power down circuit, power protection circuit
Posted in Datasheet Application | No Comments »
May 2nd, 2010
The circuit diagram below shows the Accuphase P300V stereo power amplifier, an all stage push-pull circuit configuration that forms the base of the amplifier.
P300V Stereo Power Amplifier unit assemblies both PNP and NPN power transistors with 10 parallel push-pull circuits, MOSFET cascode drive stage, NPN transistor for Class A predrive stage, Power circuits for drive stage, Input differential complementary push-pull amps, and PNP transistor for Class A predrive stage.
P300V Stereo Power Amplifier Assembly Circuit Diagram continued »
Tags: accuphase p300v, p300v circuit diagram, stereo power amplifier
Posted in Amplifier/Conditioner | No Comments »